Inconel 600 Plate

 

 

 

 

Solution strengthened Inconel 600 Cold Rolled plate offers superior resistance to oxidation in comparison to commercially pure nickel. The oxidation corrosion resistance property of Nickel Alloy 600 Shim Sheet is attributed to the presence of chromium in its alloy.

 

 Inconel 600 Plate
Inconel 600 Plate
Alloy 600 Sheet
Alloy 600 Sheet
UNS N06600 Coils
UNS N06600 Coils

 

 

Under oxidative conditions, chromium is an element which forms a bond with oxygen present in the atmosphere. This bond covers the surface of the JIS NCF 600 Hot Rolled Plates by forming a transparent, self-adhesive, strong layer referred to as passivation. A benefit of passivation is that the layer is self healing and can be regenerated in the presence of oxygen molecules in the atmosphere of the application. While the chromium part takes care of oxidation resistance, we have nickel on the other hand, which provides good combative behaviour towards reductive environments the alloy is exposed to.

 

Since nickel has superior resistance in reductive conditions, as an element, by being alloyed with the ASME SB168 Inconel Alloy 600 Strip nickel seals the transmission of several key properties, including its resistance to reductive conditions. Individually, nickel is also resilient to high temperature settings. Therefore as expected of this nickel based Werkstoff No 2.4816 Coils, the alloy has a high creep strength and can withstand elevated temperatures up to 2000 °F.

 

Unlike this heat resisting ASTM B168 UNS N06600 Cold Drawn Plate, some conventionally used alloys like grade 304 or carbon steels are more prone to creep failure. Industries like the aerospace industry, which requires superior properties prefer using the Inconel 600 Plate. Moreover, the Alloy 600 Sheet has the ability to resist caustic solutions along with steam, air as well as carbon dioxide.

 

Most common specification of Inconel 600 Plate
Specifications ASTM B168 / ASME SB168 
Alloy 600 Plate Size
1220 mm x 2440 mm, 1000 mm x 2000 mm, 2000 mm x 4000 mm, 2000 mm x 2000 mm, 1500 mm x 3000 mm
Sheet Thickness 0.1mm to 12 mm Thk
Alloy 600 Plate Form Coils, Rolls, Flats, Strip, Foils, Ring (Flange), Blank (Circle), Shim Sheet, Plain Sheet
Available Finish Cold rolled sheet (CR), Hot rolled plate (HR), 2D, 2B, SATIN (Met with Plastic Coated), BA NO(8)
Alloy 600 Plate Hardness Quarter Hard, Half Hard, Hard, Spring Hard, Soft etc.

 

Minimum Yield Strength Chart of UNS N06600 Strip
Element Melting Point Density Elongation Yield Strength (0.2%Offset) Tensile Strength
600 1413 °C (2580 °F) 8.47 g/cm3 40 % Psi – 45,000 , MPa – 310 Psi – 95,000 , MPa – 655

 

Equivalent grades of ASTM B168 Alloy 600 Plate
STANDARD UNS WNR Material Number BS GOST EN JIS AFNOR
600 N06600 2.4816 NA 13 МНЖМц 28-2,5-1,5 NiCr15Fe NCF 600 NC15FE11M

 

Chemical Element of Nickel Alloy 600 Coil
Grade Si Cu S Cr Mn C Fe Ni
600 0.50 max 0.50 max 0.015max 14.00 – 17.00 1.00 max 0.15 max 6.00 – 10.00 72.00 min

 

Available Sizes of Werkstoff No 2.4816 Plate
What is the difference between the Inconel 600 plate and sheet?

A sheet is a thinner layer of metal where are plate is usually a thicker layer of metal. In other words, the sheets are thinner plates and plates are thicker sheets. But there are limitations as to what has to be called what. The Inconel 600 material is a corrosion resistant and strong metal alloy, so it can handle stress and tension at smaller dimensions. Therefore the sheets are defined to be less than 3mm in thickness. Anything that is more than 3mm in thickness is called a plate. The sheet also has to have a minimum thickness of 0.006 inches or 0.15 mm. Anything lower than that thickness is a foil.

 

What are the different types of Inconel 600 Plate ?
ASTM B168 UNS N06600 Cold Drawn Plate
ASTM B168 UNS N06600 Cold Drawn Plate
ASME SB168 Inconel Alloy 600 Strip
ASME SB168 Inconel Alloy 600 Strip
JIS NCF 600 Hot Rolled Plates
JIS NCF 600 Hot Rolled Plates
 Werkstoff No 2.4816 Cold Rolled plate
Werkstoff No 2.4816 Cold Rolled plate

 

Supplying Inconel 600 Plate in various thickness or it any specifications that the clients.