Nickel 200 Round Bar

 

 

 

 

The ductile properties of nickel are superior in comparison to most metal grades. Since the primary constitution of ASME SB160 ni 200 alloy hex bar is nickel, its alloy inherently has very good ductility. Hence the alloy can be shaped into any desired shape such as the Nickel Alloy 200 hollow Bar.

 

Nickel 200 Round Bar
Nickel 200 Round Bar
Nickel Alloy 200 Rod
Nickel Alloy 200 Rod
UNS N02200 Hex Bar
UNS N02200 Hex Bar

 

 

Apart from being one of the most ductile metals on earth, even at higher temperatures, Nickel 200 Square Bar could be easily welded. The WERKSTOFF NR. 2.4066 Flat Bars can be fabricated with ease as well. Conventional welding practises used on austenitic stainless steel grades can be used by the 200 Nickel Alloy Cold Drawn Round Bars including an inert gas technique and resistance welding method.

 

Also, another similarity the Nickel Alloy 200 Forged Bar shares with austenitic stainless steel grades are that both alloys neither require a preheating treatment nor post-weld heat treatment. This proves to be useful for buyers who invest in the nickel alloy ni-200 hot rolled round bar, without having to worry about performing a welding operation that is non-traditional and far more expensive. Being a commercially pure grade, this wrought Nickel 200 Round Bar is a solid solution strengthened alloy. The Nickel Alloy 200 Rod also has good magnetic and magnetostrictive properties. B160 UNS N02200 Bright Bars is a good conductor of both heat and electricity.

 

Alloy 200 Round bar Available Sizes

 

Basic types of Alloy 200 Round bars
WERKSTOFF NR. 2.4066 Flat Bar
WERKSTOFF NR. 2.4066 Flat Bar
ASTM B160 UNS N02200 Bright Bar
ASTM B160 UNS N02200 Bright Bar
alloy ni-200 hot rolled round bar
alloy ni-200 hot rolled round bar
Asme Sb160 Ni 200 Alloy Cold Drawn Round Bar
Asme Sb160 Ni 200 Alloy Cold Drawn Round Bar

 

 

Nickel 200 Rod Most common specification
Standard Specifications ASTM B160 / ASTM SB160
Round bars Dimensions JIS, AISI, ASTM, DIN, BS, ASME, EN
Rod Size
5 To 500 mm
Alloy 200 Round bars Diameter 0.1 to 100 mm
200 Alloy Bars Length 100 To 3000 mm Long and Above
Round bars Finish Turned, Polished, Bright, Black, Rough, NO.4 Finish,BA Finish, Matt Finish
alloy 200 Bars Tolerance H13K9, K10, H8, K11, H12, H9, K12, H10, H11 or as per clients’ requirements
Form of Rod Square, Billet, Forging, Hex (A/F), Rectangle, Ingot, Round Etc.

 

Alloy 200 Rod Minimum Yield Strength Chart
Element Density Melting Point Tensile Strength Yield Strength (0.2%Offset) Elongation
200 8.9 g/cm3 1446 °C (2635 °F) Psi – 67000 , MPa – 462 Psi – 21500 , MPa – 148 45 %

 

Alloy 200 Bars Chemical Element
Grade C Mn Si S Cu Fe Ni Cr
200 0.15 max 0.35 max 0.35 max 0.01 max 0.25 max 0.40 max 99.0 min

 

Alloy 200 Round bars Equivalent grades
STANDARD WNR Material Number UNS JIS BS GOST AFNOR EN
200 2.4066 N02200 NW 2200 NA 11 НП-2 N-100M Ni 99.2
Difference between Nickel alloy 200 Cold rolled and hot forged bar

The commercially pure nickel 200 alloy has up to 99.6% nickel in its composition. It is expensive material and is used in specific applications. The material can come in pipes, tubes bars and rods. The bars can be produced by forging or cold rolling. The hot forging is done by forming the bars from single billet material to the desired shape. The cold rolled bars are rolled and drawn under room temperature to the desired shapes. The hot forged bars are stronger than the cold rolled ones but the cold rolled bars are dimensionally accurate than the hot forged bars.

Alloy 200 bars, rods, billets and blooms are used to make finished products suitable for Critical applications.